Metric DIN 444 Eye Bolts are bolts with an eye (loop/ring) at one end and a threaded shank at the other. They are threaded into a pre-tapped hole or secured with a nut to a structure so that a rope or cable can be attached to the loop end. Only eye bolts with shoulders should be used to support angular loads.
Get PriceCrosby® S-279 Machinery Eye Bolt UNC M-279 Crosby® S-279 Machinery Eye Bolt Metric Shoulder Type Eye Bolts Shoulder Type Eye Bolts *Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Limit. **On Request: Special threading or as forged bolts for customer conversion. •Forged Steel - Quenched
Get PriceSee Safe Lifting Chart on page 5. All rated capacities consider a straight vertical lift. Use CAUTION when lifting. Any angle beyond vertical (zero degree) will
Get PriceLifting eye bolts. BN 257. +2. DIN 580. ~ISO 3266. ~UNI 2947. ~ČSN 021369 Order now. Product data sheet (PDF). Product variants (23)
Get PriceCrosby® 275 Forged Screw Eye Bolts Crosby® 275 Forged Screw Eye Bolts > Eye Nuts. Crosby® 400 Eye Nuts Crosby® 400 Eye Nuts > Lifting Eyes. Crosby® 405 Lifting Eyes Crosby® 405 Lifting Eyes > Pad Eyes. Crosby® 264 Pad Eyes Crosby® 264 Pad Eyes > Standard Hoist Rings. Cold Temperature.
Get PriceWARNING. • Load may slip or fall if proper eye bolt assembly and lifting procedures are not used. • A falling load can seriously injure or kill.
Get PriceM St 4.6 Standard 16180 5-4 M St.St. A2 Standard 51790 5-5 M St.St. A4 Standard 55790 5-5 16180 Eye bolt F11D Thread Metric thread Material Steel Class 4.6 Packaging Standard d1 x
Get Priceshoulder pattern eye bolts. Machinery Lifting Eye Bolts in this catalog, and other catalogs to which you may refer, could show a higher Working Load Limit (WLL), or Rated Capacity (RC). Lifting Eye Bolts have a safety factor of five times the WLL/RC with proper seating and full thread engagement. 3. The RC of an eye bolt is determined from a
Get PriceLong Shank code WIR15662 did conform to BS 529 Part 1 1944 but this standard has now been withdrawn. Crosby Forged Steel Rated Eye Bolts With Nuts. [Type G277]
Get Priceplease refer to the standard, DIN 580 for eye bolts or DIN 582 for eye nuts. It is required that the products are regularly inspected and that the
Get PriceEye Bolts/ Eye Nuts Eye bolts and eye nuts are used for lifting machines, appliances or any other objects which cannot be lifted by hand or by fork lift truck. Applications Range The eye bolts and eye nuts are manufactured from C15 steel, drop forged and with metric thread. Each eye bolt and eye nut is individually stamped with:
Get PriceThe above eye bolts comply to British Standards as follows: Short Shank code WIR15112 to BS 4278 Part 1 1984. [The scope of this standard starts at M12 - the M10 is machined from an M12 forging].
Get PriceDIN 580 Specification. Lifting Eye Bolts. DIN 580 Scope. DIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in
Get Priceplain & shoulder eye bolts shoulder eye bolts the actual load a single eye bolt can lift is referred to as "riggers load." engineers capacity is the allowable tension in the eye of the lifting rig as it is applied to the eye bolt. it is necessary to determine the tension in each rig leg before sizing the eye bolt. shoulder eye bolts united part no.
Get Priceas standard. When installing lifting eye bolts it is The introduced force must act in the direction of the eye bolt plane (illustration right,
Get PriceThe ASME B30.26 standard is applicable only to carbon steel eye bolts specifies that carbon steel eye bolts are only to be used above -1°C. For environments below -1°C the standard is ASTM F541-12. In order to achieve certification with this standard the eye bolt must be made of alloy steel and be permanently marked with the letter A denoting
Get PriceDIN 580 Specification specifies the properties of steel and stainless steel eyebolts and provides information on their correct use in lifting operations (as part of slings and as load handling equipment). Eye bolts according to this standard can be used in a temperature range from −20 ° C to +200 ° C without any restriction of the load capacity.
Get PriceCrosby® S-279 Machinery Eye Bolt UNC M-279 Crosby® S-279 Machinery Eye Bolt Metric Shoulder Type Eye Bolts Shoulder Type Eye Bolts *Ultimate Load is 5 times the Working Load Limit. Maximum Proof Load is 2 times the Working Load Limit. **On Request: Special threading or as forged bolts for customer conversion. •Forged Steel - Quenched
Get PriceFatigue rated at 1-1/2 times the Working Load Limit at 20,000 cycles. ! All Bolts Hot Dip galvanized after threading (UNC). ! Furnished with standard Hot Dip
Get PriceEye Bolt 134 Care In Use 134 Eye Nut 135 Eye Bolt - Bs4278 With Metric Sizing 136 of a standard sized nut. Where an Eye Bolt is used with a tapped hole in a plate the length of thread engagement should be at least the nominal di-ameter of the thread. Where the undercut is not sufficient to allow for an adequate engagement of the collar, a
Get PriceSTANDARD SHANK LENGTHS. PLAIN & SHOULDER PATTERN. Stock Numbers. Dimensions - Inches. Plain. Shoulder. Shank. Eye. Overall Length. Plain. Overall Length.
Get Price